__________________________________________________________ The U.S. Department of Energy Computer Incident Advisory Capability ___ __ __ _ ___ / | /_\ / \___ __|__ / \ \___ __________________________________________________________ INFORMATION BULLETIN Cisco Products Vulnerable to DoS via Crafted ICMP Messages [Cisco Security Advisory Document ID: 64520] April 14, 2005 12:00 GMT Number P-181 [REVISED 25 Apr 2005] [REVISED 15 Jun 2005] ______________________________________________________________________________ PROBLEM: Internet Control Message Protocol (ICMP) can be used to perform a number of Denial of Service (DoS) attacks against TCP. PLATFORM: Cisco products that run Cisco IOS and that have PMTUD enabled, either by default or because they have been explicitly configured to do PMTUD, are affected. All versions of IOS are impacted. DAMAGE: Successful attacks may cause connection resets or reduction of throuhput in existing connections. These attacks only affect sessions terminating or originating on a vulnerable device itself. Traffic that passes through a device but is destined elsewhere is not affected. SOLUTION: Upgrade the software as directed. ______________________________________________________________________________ VULNERABILITY The risk is LOW. The attacks may result in a DoS, but not to ASSESSMENT: remote code execution or unauthorized access. The Cisco PSIRT is not aware of any malicious use of these vulnerabilities. ______________________________________________________________________________ LINKS: CIAC BULLETIN: http://www.ciac.org/ciac/bulletins/p-181.shtml ORIGINAL BULLETIN: Cisco Security Advisory Document ID: 64520 http://www.cisco.com/en/US/products/products_security_ advisory09186a0080436587.shtml ADDITIONAL LINK: Microsoft Security Bulletin MS05-019 (893066) http://www.microsoft.com/technet/security/Bulletin/MS05- 019.mspx ______________________________________________________________________________ REVISION HISTORY: 04/25/2005 - updated bulletin to reflect Revision 1.2 of Cisco Security Advisory Document ID: 64520. Some changes include: modifying the list of vulnerable and non-vulnerable products, adding link for Cisco IOS XR download, as well as several other modifications. 06/15/2005 - revised to add a link to Microsoft Security Bulletin MS05-019. [***** Start Cisco Security Advisory Document ID: 64520 *****] Crafted ICMP Messages Can Cause Denial of Service Document ID: 64520 Revision 1.2 Last Updated 2005 April 22 2230 UTC (GMT) For Public Release 2005 April 12 1200 UTC (GMT) -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Contents Summary Affected Products Details Impact Software Versions and Fixes Obtaining Fixed Software Workarounds Exploitation and Public Announcements Status of This Notice: FINAL Distribution Revision History Cisco Security Procedures -------------------------------------------------------------------------------- Summary A document that describes how the Internet Control Message Protocol (ICMP) could be used to perform a number of Denial of Service (DoS) attacks against the Transmission Control Protocol (TCP) has been made publicly available. This document has been published through the Internet Engineering Task Force (IETF) Internet Draft process, and is entitled "ICMP Attacks Against TCP" ( draft-gont-tcpm-icmp- attacks-03.txt ). These attacks, which only affect sessions terminating or originating on a device itself, can be of three types: Attacks that use ICMP "hard" error messages Attacks that use ICMP "fragmentation needed and Don't Fragment (DF) bit set" messages, also known as Path Maximum Transmission Unit Discovery (PMTUD) attacks Attacks that use ICMP "source quench" messages Successful attacks may cause connection resets or reduction of throughput in existing connections, depending on the attack type. Multiple Cisco products are affected by the attacks described in this Internet draft. Cisco has made free software available to address these vulnerabilities. In some cases there are workarounds available to mitigate the effects of the vulnerability. This advisory is posted at http://www.cisco.com/warp/public/707/cisco-sa-20050412- icmp.shtml. The disclosure of these vulnerabilities is being coordinated by the National Infrastructure Security Coordination Centre (NISCC), based in the United Kingdom. NISCC is working with multiple vendors whose products are potentially affected. Its posting can be found at: http://www.niscc.gov.uk/niscc/docs/re-20050412- 00303.pdf?lang=en. Affected Products Vulnerable Products Cisco IOS Cisco products that run Cisco IOSŪ and that have PMTUD enabled, either by default or because they have been explicitly configured to do PMTUD, are affected. All versions of IOS are impacted. The severity of the exposure depends upon the protocols and applications that rely on specific ICMP messages to perform PMTUD. IOS is not vulnerable to attacks that make use of ICMP "hard" error or "source quench" messages. To determine the software running on a Cisco product, log in to the device and issue the show version command to display the system banner. Cisco IOS Software will identify itself as "Internetwork Operating System Software" or simply "IOS." The image name will be displayed between parentheses shortly after this identification (possibly in the next line), followed by "Version" and the IOS release name. Other Cisco devices will not have the show version command or will give different output. The following example identifies a Cisco product running IOS release 12.2(15)T14 with an installed image name of C806-K9OSY6-M: gw>show version Cisco Internetwork Operating System Software IOS (tm) C806 Software (C806-K9OSY6-M), Version 12.2(15)T14, RELEASE SOFTWARE (fc4) [...] The following protocols make use of PMTUD and if enabled in the network may cause IOS devices to be vulnerable to PMTUD attacks. Transmission Control Protocol over Internet Protocol (IP) Version 4: if an IOS device establishes TCP sessions with other devices, for example, to speak Border Gateway Protocol (BGP) with other peers, it may be vulnerable to crafted ICMP "fragmentation needed and DF bit set" error messages if PMTUD is enabled. PMTUD is disabled by default for TCP in IOS. PMTUD is enabled if the command ip tcp path- mtu-discovery is present in the device configuration. Transmission Control Protocol over Internet Protocol Version 6 (IPv6): PMTUD is enabled by default for IPV6; therefore, devices configured for IPv6 are vulnerable to PMTUD attacks if they are running services that rely on TCP, like BGP. If the device is just forwarding IPv6 traffic, i.e., it does not establish TCP sessions with other hosts, then it is not affected. IP Security (IPSec): when an IOS device is configured to use IPSec, PMTUD is enabled by default, and therefore, the device may be affected by the PMTUD attack described in this document. An IOS device is configured for IPSec if either crypto map or tunnel protection is applied to an interface. For example: crypto ipsec profile IPSEC_PROFILE [...] ! crypto map MYMAP 1 ipsec-isakmp [...] ! interface Tunnel0 tunnel protection ipsec profile IPSEC_PROFILE [...] ! interface Ethernet1 crypto map MYMAP [...] Generic Routing Encapsulation (GRE) and IPinIP: devices configured to use these tunneling protocols are vulnerable to crafted ICMP "fragmentation needed and DF bit set" messages if PMTUD is enabled. PMTUD is disabled by default for these two protocols. The device is vulnerable if the command tunnel path-mtu-discovery is present in the configuration. Layer 2 Tunneling Protocol Version 2 (L2TP) and Layer 2 Tunneling Protocol Version 3 (L2TPv3): devices configured to use these tunneling protocols are vulnerable to crafted ICMP "fragmentation needed and DF bit set" messages if PMTUD is enabled. PMTUD is disabled by default for these protocols. A device running L2TP is vulnerable if the command ip pmtu appears in the device's configuration. Note: L2TP (version 2) and L2TPv3 (version 3) are two different and independent protocols. Both are affected, but throughout the rest of this document we will refer to them as one since they are affected in the same manner. In addition to IOS-based routers, the following devices also run Cisco IOS or software based on Cisco IOS and are therefore vulnerable: The Catalyst 4000 and 6000 switches when running IOS in either hybrid (Supervisor Engine running CatOS and Multilayer Switch Feature Card running IOS) or native mode (Supervisor Engine running IOS.) Cisco Aironet Wireless LAN Access Points and Bridges. Catalyst 2900XL, 2900XL-LRE, 3500XL, 2940, 2950, 2950-LRE, 2955, and 2970 series switches. Catalyst 2948G-L3, 3550, 3560, 3750, and 3750-ME series switches. The Communication Media Module (CMM) Cisco Optical Network Solutions (ONS) products: the ML and SL blades in the ONS 15454, and the ONS 15530/15540. Cisco DistributedDirector. Non-IOS Products The following non-IOS-based products are also vulnerable: Cisco CRS-1: the CRS-1 runs IOS XR, which is vulnerable to PMTUD attacks and to attacks that use ICMP "hard" error messages if the CRS-1 establishes TCP sessions with other devices in applications like BGP. PMTUD is disabled by default in IOS XR. PMTUD is enabled if the command tcp path-mtu-discovery is present in the device configuration. Use the show version command to obtain the version of the running IOS XR software. Cisco PIX Security Appliance is vulnerable to PMTUD attacks if it is configured to use IPSec. The only traffic that is affected is traffic going through the particular IPSec tunnel that has been attacked. IPSec is not enabled by default on the Cisco PIX Security Appliance. The Cisco PIX Security Appliance is using IPSec if the device configuration shows a crypto map applied to an interface through the command crypto map interface . The show version command can be used to determine the running version of the Cisco PIX Security Appliance software. Please note that version 7.0 and later of the PIX Security Appliance software is not affected by these vulnerabilities. Cisco IP Phones 7940/7960 with Skinny Client Control Protocol (SCCP) firmware. 7940/7960 with Session Initiation Protocol (SIP) firmware. 7970 with Skinny Client Control Protocol firmware (vulnerable only to crafted ICMP "hard" error messages) The version of the firmware running on your Cisco IP Phone can be found by pressing the "Settings" button of your phone and selecting the "Status" menu options. Cisco Catalyst 6000 Voice E1/T1 and Services Module (WS-X6608-E1 and WS-X6608-T1) running Digital PRI Gateway, Conference Bridge, or Transcoder/MTP firmware; and Cisco 6000 FXS Analog Interface Module (WS-X6624-FXS) are vulnerable to crafted ICMP "hard" errors, as well as to crafted ICMP "source quench" messages. To obtain the version of the 6608 and 6624 firmware, log in to your Catalyst 6500 series switch and issue the show version command. Cisco 11000 and 11500 Content Services Switches (CSS). Global Site Selector (GSS). Cisco ONS products: ONS 15302 and ONS 15305. Cisco MDS 9000 Series Multilayer Switches. Cisco VPN 5000 concentrator. Cisco MGX-8250 (PXM-1 based) and MGX-8850 (PXM-1E and PXM-45 based) - vulnerable on the control plane only; switching services are not impacted. Cisco Content Switching Module (CSM) - vulnerable control plane only; switching services are not impacted. Microsoft Security Bulletin MS05-019 states that Microsoft Windows is vulnerable to PMTUD attacks and to attacks based on ICMP "hard" error messages. The following voice and IP communication products are shipped with, and run on top of, the Microsoft Windows operating system. The customization of Microsoft Windows made by Cisco and included with these products has PMTUD disabled by default starting with release 2000.2.5 (releases 2000.2.4 and before use the Microsoft default which is to enable PMTUD.) These products are vulnerable to attacks based on ICMP "hard" errors as well as to PMTUD attacks (if PMTUD is enabled): Cisco Call Manager Cisco IP Interactive Voice Response Cisco IP Call Center Express Cisco IP Queue Manager Cisco Personal Assistant Cisco Emergency Responder Cisco Conference Connection Cisco Customer Voice Portal (previously Internet Service Node) Cisco MeetingPlace The following products use non-Cisco-customized versions of Microsoft Windows. PMTUD is enabled by default on Microsoft Windows, so these products may be vulnerable to PMTUD attacks if this default setting has not been changed, and are vulnerable to attacks based on ICMP "hard" error messages, as described in Microsoft Security Bulletin MS05-019 : Cisco Unity Cisco IP Contact Center Enterprise Edition To verify whether PMTUD is enabled in the version of Microsoft Windows used by your Cisco product, please check the value of the following registry key: HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Tcpip\ Parameters\EnablePMTUDiscovery If this registry key is present then PMTUD is enabled or disabled based on the value of the key. If they key is not present, PMTUD is enabled. The Cisco Secure ACS Solution Engine, also known as the Cisco Secure ACS Appliance, is based on Microsoft Windows, and therefore is vulnerable to PMTUD attacks and to attacks based on ICMP "hard" error messages. However, recent versions of the ACS Solution Engine ship with Cisco Security Agent (CSA), which is configured to block all incoming ICMP messages. Under this situation the Cisco Secure ACS Solution Engine is not vulnerable to any of the attacks described in this document. To determine if you have CSA installed and working, you can try sending ICMP echo requests (ping) to the ACS appliance. If ICMP echo replies are received CSA is not enabled or installed. To check to see if CSA is available go to "System Configuration:Upgrade Appliance" and see what version is installed. Then go to "System Configuration:Appliance Configuration" and see if CSA is enabled. Products Confirmed Not Vulnerable The following products are not vulnerable: Cisco Firewall Services Module (FWSM) for Cisco Catalyst 6500 Series and Cisco 7600 Series. Cisco Guard and Cisco Traffic Anomaly Detector Denial of Service mitigation appliances. Catalyst Switches. The following Catalyst switches do not run Cisco IOS and therefore are not affected by the vulnerabilities described in this document: 1200 1700 1900 2100 28xx 2948G-GE-TX 2900, 2902, 2926T and 2926G 3000, 3100, 3200 3900 5000 The Catalyst 4000 and 6000 switches can run CatOS or IOS. When running CatOS, they are not vulnerable unless a Multilayer Switch Feature Card (MSFC) is present (since the MSFC runs IOS.) When running IOS, they are vulnerable as described above in the Vulnerable Products section. Cisco ONS products: ONS 15327 Metro Edge Optical Transport Platform, ONS 15454 Optical Transport Platform (MSPP and MSTP), ONS 15531/15532 T31 OMDS Metro WDM System, ONS 15216 EDFA3/EDFA2/OADM, ONS 15310 CL. Cisco IP Phones ATA 186/188 7902/05 7910 7912 7920 Cisco VG248 Analog Phone Gateway Cisco VPN 3000 Series Concentrators, VPN 3002 Hardware Clients, and the VPN Software Client (please note that the VPN Software Client itself is not vulnerable but the operating system the VPN clients runs on may be vulnerable. Please check with your operating system vendor.) Cisco BTS 10200 Softswitch Content Engines, Content Routers, and Content Distribution Managers running Cisco Application and Content Networking System (ACNS) software. Cisco LocalDirector. Summary of Vulnerable Products The following table summarizes how Cisco products are affected by the vulnerabilities described in this document: Product Hard Error PMTUD Source Quench IOS Not affected Affected Not affected IOS XR Affected Affected Not affected IP Phones Affected Affected Affected Cisco PIX Security Appliance Not affected Affected Not affected Catalyst 6608 and 6624 Affected Not affected Affected Cisco 11000 and 11500 Not affected Not affected Affected Cisco GSS Not affected Not affected Affected MDS 9000 Not affected Affected Affected Cisco VPN 5000 Concentrator Not affected Affected Not affected Some ONS products Not affected Affected Not affected Cisco MGX-8250 and MGX-8850 Affected Affected Affected Cisco Content Switching Module Not affected Not affected Affected Voice and IP Communication Products Using Cisco-Customized Microsoft Windows Affected Affected Not affected Cisco ACS Solution Engine Affected Affected Not affected Please refer to the Details section for additional information since within one product family different models may be affected differently. Details The Internet Control Message Protocol is an integral part of the Transmission Control Protocol/Internet Protocol (TCP/IP) protocol suite that is used to report error conditions and provide diagnostic information. ICMP error messages can be generated by both end systems and intermediate systems, i.e., routers. End systems and intermediate systems react to error messages received via ICMP in different ways depending on the type of error that is being reported. The types of errors that can be reported via ICMP fall into two categories: "soft" errors and "hard" errors. RFC 1122 ("Requirements for Internet Hosts - Communications Layers" - http://www.ietf.org/rfc/rfc1122.txt ), defines three "hard" errors ("protocol unreachable", "port unreachable", and "fragmentation needed and Don't Fragment bit set") and five "soft" errors ("network unreachable", "host unreachable", "source route failed", "time exceeded", and "parameter problem".) "Source quench" is another ICMP error message that can be generated by Internet hosts, and while RFC 1122 does not clearly classify it as "soft" or "hard", it should be considered as a soft error because of the way this message type should be handled by hosts that receive it: hosts should cut back for a period of time the rate at which they are sending data to the host that generated the ICMP "source quench" message, and then gradually increase the transmission rate again. It is important to note that the "fragmentation needed and Don't Fragment bit set" (type 3, code 4) message is used by an important mechanism called Path MTU Discovery, documented in RFC 1191 ("Path MTU discovery" - http://www.ietf.org/rfc/rfc1191.txt ). PMTUD allows some protocols of the TCP/IP protocol suite to dynamically find the MTU of a path so IP fragmentation is minimized and bandwidth can be used more efficiently. This mechanism is not mandatory for Internet hosts, but those that implement it need to treat ICMP "fragmentation needed and DF bit set" messages as "soft" errors. A good reference to understand how IP fragmentation works and the role that PMTUD plays in reducing fragmentation is the Cisco white paper "IP Fragmentation and PMTUD", available at http://www.cisco.com/en/US/tech/tk827/tk369/technologies_white_paper09186a00800d697 9.shtml. Making a distinction between the types of errors ("soft" versus "hard") that can be reported via ICMP is important because it dictates how Internet hosts will respond to them. In general, connection-oriented protocols like TCP should abort an existing connection in response to an ICMP "hard" error message, and Internet hosts should try to correct the error condition that elicited the receipt of an ICMP "soft" error message. An IETF Internet Draft entitled "ICMP Attacks Against TCP" (draft-gont-tcpm-icmp- attacks-03.txt ) that describes how the ICMP protocol can be used to perform a number of Denial of Service attacks against the TCP protocol has been made publicly available. These attacks require knowledge of the IP addresses and ports (in the case of TCP) that two Internet hosts are using to communicate with each other and can cause connection resets and reduction of throughput in existing connections. Note: these attacks only affect sessions terminating or originating on a device itself, not transit traffic; i.e., traffic that passes through a device, but is destined elsewhere is not affected. Attacks Based on Crafted Hard ICMP Error Messages Upon receipt of a "hard" ICMP error message, an Internet host must abort the connection with the host to which the ICMP error message applies. This host is not necessarily the system that generated the ICMP message, but it is uniquely identified through the IP header and transport protocol data embedded in the ICMP payload. The reason for this is that "hard" errors represent serious network problems for which there is not a possibility for recovery. Crafted "hard" ICMP error messages could cause an Internet host to incorrectly abort an existing connection when in reality there are no network problems. This type of attack is classified as a "blind connection-reset" attack in the Internet Draft draft-gont- tcpm-icmp-attacks-03.txt . PMTUD Attacks Crafted "fragmentation needed and DF bit set" ICMP messages can be used to set a connection's Path MTU to a very low, impractical value, if an Internet host is performing PMTUD. This value can cause higher layer protocols to start timing out because of a very low throughput, even though the connection is still in the established state. This type of attack is classified as a "throughput-reduction" attack in the Internet Draft draft-gont-tcpm-icmp-attacks-03.txt . Per the PMTUD algorithm described in RFC 1191 , implementations must "age" cached MTU values, which means that the MTU will go back to its optimum size, a process that can take up to 10 minutes ( RFC 1191 suggests 10 minutes, but this is not a requirement and therefore it is implementation-dependent.) Please note, however, that if an attacker continues to send crafted ICMP "fragmentation needed and DF bit set" messages to a vulnerable host, the cached MTU will never age, causing a continuous denial-of-service condition. As mentioned before, the ICMP "fragmentation needed and DF bit set" message is considered a "hard" error per RFC 1122 if the Internet host receiving it is not performing PMTUD. This means that a PMTUD attack also has the potential to cause a connection reset. For protocols that make use of a "transport layer" MTU to minimize the risk of fragmentation, like TCP and its Maximum Segment Size (MSS) variable, a good way to determine if a connection is suffering from a successful attack is to monitor the value of this "transport layer" MTU - an unreasonably low value may indicate that an attack has been performed. An example of how to do this in Cisco IOS will be provided later in this document. Note: several common protocols make use of TCP, and therefore may be affected by PMTUD attacks. Some examples include BGP, the Hyper Text Transfer Protocol (HTTP - used in the World Wide Web), the Simple Mail Transfer Protocol (SMTP - used for transferring electronic mail), and Secure Shell (SSH). Some protocols in the IBM suite like Data-Link Switching (DLSw), Serial Tunneling (STUN), and Block Serial Tunneling (BSTUN) can be configured to use TCP as their transport protocol. The Domain Name System (DNS) normally uses User Datagram Protocol (UDP) but in some situations (large zone transfers, for example) it also uses TCP. Attacks Based on Crafted Source Quench ICMP Messages As mentioned before, Internet hosts are supposed to cut back the rate at which they send data to another host that generated an ICMP "source quench" message. While the actual response to an ICMP "source quench" message varies by TCP/IP implementation and by the transport layer protocol in use, in general, hosts receiving an ICMP "source quench" message should trigger a congestion avoidance algorithm. In the case of a host using TCP to communicate with another, if an ICMP "source quench" message is received the recommended procedure per RFC 1122 is to trigger a "slow start", as if a retransmission timeout had occurred. RFC 2001 ("TCP Slow Start, Congestion Avoidance, Fast Retransmit, and Fast Recovery Algorithms" - http://www.ietf.org/rfc/rfc2001.txt ) describes the "slow start" and "congestion avoidance" algorithms used in modern implementations of TCP and states that in practice, the "slow start" and "congestion avoidance" algorithms are implemented together. The lower rate at which the sending host transmits data allows the host that generated the ICMP "source quench" message to process and empty its receive buffers. Crafted "source quench" ICMP messages can be used to decrease the rate at which a host is sending data. While over time, as long as no additional Source Quench messages are received, the window size will increase to a reasonable value, a crafted "source quench" message can potentially reduce communication efficiency significantly. If an attacker succeeds in periodic transmission of crafted ICMP "source quench" messages to a vulnerable device, a prolonged degradation of service for that connection may occur. This type of attack is classified as a "throughput-reduction" attack in the Internet Draft draft-gont-tcpm-icmp-attacks-03.txt. How Cisco Products Are Affected Different Cisco products are affected in different ways to the ICMP attacks described in this document. In some cases, some products are affected when specific configurations or network protocols are in use. What follows is a description of how vulnerable products are affected and under what configurations. Information about specific Cisco bug IDs for each product is presented. Cisco IOS Cisco IOS is not vulnerable to attacks that make use of ICMP "hard" error messages because IOS checks whether a connection is in the "established" state, and takes action only for connections in the "non-established" state. In addition, IOS does not process ICMP "source quench" messages and therefore, is not vulnerable to attacks that are based on crafting this type of message. IOS is vulnerable to PMTUD attacks as described in the Vulnerable Products section. This means that an attacker could change the Path MTU by crafting an ICMP "fragmentation needed and DF bit set" message ("packet too big" message in the case of IPv6.) The following list provides the Cisco bug IDs for the PMTUD vulnerabilities in different protocols in IOS: All protocols that make use of PMTUD: CSCef60659 ( registered customers only) -- More stringent checks required for ICMP unreachables. Transmission Control Protocol over Internet Protocol Version 4: CSCed78149 ( registered customers only) -- TCP connections over IP version 4 doing PMTUD are vulnerable to crafted ICMP packets. A good way to verify whether a connection is suffering from the effects of a PMTUD attack is by looking at the MSS value of the connection. For BGP sessions the command show ip bgp neighbors | include data segment will display the MSS (denoted as max data segment), as in the following example: Router#show ip bgp neighbors | include data segment Datagrams (max data segment is 1460 bytes): Router# The official minimum MTU is 68 bytes, although in today's Internet a MSS less than 576 bytes should be considered suspicious. Section 7 of RFC 1191 contains a list of common MTU values used on the Internet. For other TCP connections, the Transmission Control Block (TCB) of a specific connection must be determined using the command show tcp brief, and then this TCB must be used in the command show tcp tcb | include data segment, which will display the MSS (denoted again as max data segment): Router#show tcp brief TCB Local Address Foreign Address (state) 00E97148 192.168.100.1.23 192.168.100.1.11002 TIMEWAIT 00E97A78 192.168.100.1.23 192.168.100.1.11003 ESTAB 00E975E0 192.168.100.1.11003 192.168.100.1.23 ESTAB Router#show tcp tcb 0x00E975E0 | include data segment Datagrams (max data segment is 1474 bytes): Router# Please note that this technique can also be used for TCP over IPv6. Transmission Control Protocol over Internet Protocol Version 6: CSCef61610 ( registered customers only) -- Incorrect handling of ICMPv6 messages can cause TCP performance problems. IPSec: CSCsa59600 ( registered customers only) -- IOS IPSec connections may be vulnerable to crafted ICMP packets which may cause IPSec to use very small PMTU values for a given flow. After the PMTU has been decreased by a crafted ICMP "fragmentation needed and DF bit set" message, if no additional ICMP "fragmentation needed and DF bit set" messages are received, the learned MTU will be active for 10 minutes, after which the PMTU is restored to the first-hop data-link MTU, per RFC 1191 . A way to verify whether an IPSec tunnel is suffering from the effects of a PMTUD attack is by running the command show crypto ipsec sa | include mtu, as in the following example: Router#show crypto ipsec sa | include mtu path mtu 1500, media mtu 1500 Router# Generic Routing Encapsulation and IPinIP: CSCef44699 ( registered customers only) - - GRE and IPinIP tunnels may be vulnerable to crafted ICMP packets. A way to verify whether a GRE or IPinIP tunnel is suffering from the effects of a PMTUD attack is by running the command show interface tunnel | include Path MTU, as in the following example: Router#show interface tunnel 0 | include Path MTU Path MTU Discovery, ager 10 mins, MTU 1476, expires never Please note that in the case of these tunneling protocols, the ICMP error message does not include enough information about the GRE or IPinIP packet that elicited the error to be able to properly authenticate the message. For this reason the Cisco Bug ID CSCef44699 ( registered customers only) adds a new command that allows users to specify the minimum Path MTU they expect to have across their GRE tunnels. The new command is tunnel path-mtu-discovery min-mtu and is available under tunnel interface configuration mode. When this command is in use, and the device receives an ICMP "fragmentation needed and DF bit set" message that advertises a next-hop Path MTU less than the configured minimum Path MTU, the device will produce a log message similar to the following: %TUN-5-IGNOREICMPMTU Tunnel1 ignoring received ICMP Type 3 Code 4, due to pmtud min-mtu setting Layer 2 Tunneling Protocol Version 2 and Layer 2 Tunneling Protocol Version 3: for L2TP version 2 the Cisco bug ID is CSCsa52807 ( registered customers only) -- L2TPv2 doing PMTUD vulnerable to spoofed ICMP packets. For L2TP version 3 the bug ID is CSCef43691 ( registered customers only) -- Connections using Layer 2 Tunneling Protocol v3 (L2TPv3) and doing PMTU discovery may be vulnerable to crafted ICMP packets. A way to verify whether a L2TPv2 session is suffering from the effects of a PMTUD attack is by running the command show vpdn session all | include Session MTU, as in the following example: Router#show vpdn session all | include Session MTU Session MTU is 68 bytes For L2TPv3, a PMTUD attack can be identified by running the command show l2tun session all | include PMTU, as in the following example: Router#show l2tun session all | include Session MTU Session PMTU enabled, path MTU is 68 bytes Session PMTU enabled, path MTU is 68 bytes Session PMTU enabled, path MTU is 68 bytes Please note that in the case of L2TPv2, the ICMP error message does not include enough information about the L2TPv2 packet that elicited the error to be able to properly authenticate the message. For this reason, the fix for Cisco Bug ID CSCsa52807 ( registered customers only) adds a new commands that allow users to specify the minimum and maximum Path MTU they expect to have across their L2TPv2 tunnels. The new commands are vpdn pmtu minimum and vpdn pmtu maximum and are available under vpdn-group configuration mode. When these commands are in use, and the device receives an ICMP "fragmentation needed and DF bit set" message that advertises a next-hop Path MTU outside the minimum and maximum range, the device will produce the following log message: %VPDN-5-IGNOREICMPMTU Ignoring received ICMP Type 3 Code 4, due to pmtu min or max setting IOS XR IOS XR is vulnerable to attacks based on ICMP "hard" error messages, as well as to PMTUD attacks. The Cisco Bug ID that documents this vulnerability is CSCef45332 ( registered customers only) -- CRS-1 connections may be vulnerable to crafted ICMP packets. IOS XR does not process ICMP "source quench" messages, so it is not vulnerable to attacks based on this type of message. Cisco IP Phones Different models of Cisco IP Phones are vulnerable to attacks based on ICMP "hard" error messages, ICMP "source quench" messages, and/or PMTUD attacks. CSCef46728 ( registered customers only) -- 7940/7960 IP Phone with SCCP firmware may be susceptible to crafted ICMP "hard" error messages. CSCef54947 ( registered customers only) -- 7970 IP Phone with SCCP firmware may be susceptible to crafted ICMP "hard" error messages. CSCef54204 ( registered customers only) -- 7940/7960 IP Phone with SIP firmware may be vulnerable to crafted ICMP "source quench" error messages. Please note that a 7940/7960 IP Phone with SIP firmware does not support TCP for signaling, so only telnet sessions into the phone (for management) and short-lived HTTP sessions from the phone (to servers providing directory services, for example) are affected by this vulnerability. CSCef54206 ( registered customers only) -- 7940/7960 IP Phone with SIP firmware may be vulnerable to crafted ICMP "hard" error messages. Please note that a 7940/7960 IP Phone with SIP firmware does not support TCP for signaling, so only telnet sessions into the phone (for management) and short-lived HTTP sessions from the phone (to servers providing directory services, for example) are affected by this vulnerability. Cisco PIX Security Appliance A PIX Security Appliance with IPSec configured will actively participate in PMTUD per RFC 1191 and RFC 2401 ("Security Architecture for the Internet Protocol" - http://www.ietf.org/rfc/rfc2401.txt .) This means that the PIX Security Appliance can dynamically discover and adjust its path MTU for a given IPSec flow when it receives an ICMP "fragmentation needed and DF bit set" message. Under this scenario, the PIX Security Appliance is also vulnerable to crafted ICMP type 3 code 4 messages that try to set the path MTU to a very low value. This vulnerability is documented in the Cisco Bug ID CSCef57566 ( registered customers only) -- A PIX Security Appliance with IPSec configured can be susceptible to crafted ICMP packets suggesting a very small PMTU for a path or a Security Association. This symptom is observed when IPSec is configured for PMTUD, which is turned on automatically when IPSec is configured on the PIX Security Appliance. Catalyst 6608 and 6624 The Cisco Catalyst 6000 Voice E1/T1 and Services Module (WS-X6608-E1 and WS-X6608- T1) running Digital PRI Gateway, Conference Bridge, or Transcoder/MTP firmware Cisco 6000 FXS Analog Interface Module (WS-X6624-FXS) are vulnerable to attacks based on ICMP "hard" error and "source quench" messages. The Cisco Bug ID that documents these vulnerabilities is CSCsa60692 ( registered customers only) -- ICMP Hard error handling. Cisco 11000 and 11500 Content Services Switches The Cisco 11000 and 11500 Content Services Switches are vulnerable to attacks based on ICMP "source quench" messages on the management port; they are not vulnerable on the network ports. The CSS does not perform PMTUD and therefore is not vulnerable to PMTUD attacks. The Cisco Bug ID that documents the vulnerability to ICMP "source quench" messages is CSCeh45454 ( registered customers only) -- ICMP error packet attacks against TCP. Cisco Global Site Selector The Cisco Global Site Selector version 1.2 and earlier is vulnerable to attacks based on ICMP "source quench" messages. It is not vulnerable to attacks based on ICMP "hard" error messages or to PMTUD attacks. The Cisco Bug ID that documents the vulnerability to ICMP "source quench" messages is CSCeh20083 ( registered customers only) -- ICMP error packet attacks against TCP. Cisco MDS 9000 Series Multilayer Switches The Cisco MDS 9000 Series Multilayer Switch is vulnerable to PMTUD and "source quench" attacks. The Cisco Bug ID that documents this vulnerability is CSCeh04183 ( registered customers only) -- ICMP attacks against TCP. Cisco ONS Products The affected Cisco ONS products are vulnerable to PMTUD attacks only. VPN 5000 Concentrator The VPN 5000 concentrator is vulnerable to PMTUD attacks. ICMP "source quench" messages are only processed to keep message counts, but not for avoiding congestion. Therefore, this device is not vulnerable to attacks based on this type of messages. The Cisco Bug ID that documents the PMTUD vulnerability is CSCeh59823 ( registered customers only) -- ICMP 3/4 messages may affect IPSec sessions. Cisco MGX-8250 and MGX-8850 The Cisco MGX1 (PXM1) and MGX2 (PXM45s, PXM1E) are vulnerable to ICMP "source quench" attacks, PMTUD attacks, and ICMP "hard" error attacks on the management side. Please note that this affects management TCP connections (telnet, SSH) and not switching services. The Cisco Bug IDs that track these vulnerabilities are CSCeh65337 ( registered customers only) for the Cisco MGX1 and CSCeh63449 ( registered customers only) for the Cisco MGX2. Cisco Content Switching Module The Cisco Content Switching Module is vulnerable to ICMP "source quench" attacks on TCP-based management connections to the device. Traffic going through the device is not impacted. Cisco Products That Include Versions of Microsoft Windows Voice and IP communication products that use a Cisco-customized version of Microsoft Windows, and the ACS Solution Engine, which also includes a version of Microsoft Windows, are vulnerable to PMTUD attacks and to attacks based on ICMP "hard" error messages. For details about these vulnerabilities in Microsoft Windows, please refer to Microsoft Security Bulletin MS05-019 . There is no Cisco Bug ID to track these vulnerabilities in the voice and IP communication products. For the ACS Solution Engine, the Cisco Bug ID used to track these vulnerabilities is CSCeh62307 ( registered customers only) . Impact Successful exploitation of attacks using crafted ICMP "hard" error messages may result in connections being dropped. Successful exploitation of attacks based on "fragmentation needed and DF bit set" (or PMTUD attacks) and ICMP "source quench" error messages may result in connections being throttled to very low throughput. While throughput is low, the output buffer of a sending host could overflow or packets could be dropped or be unnecessarily fragmented, which may affect applications and communication efficiency. Accordingly, crafted ICMP packets could interfere with network protocols, such as the Border Gateway Protocol, Label Distribution Protocol (LDP) and DLSw. In addition to causing low throughput, a PMTUD attack can also cause high Central Processing Unit (CPU) utilization and extra memory consumption on the receiving host because the CPU will spend time and memory buffers to reassemble the incoming fragmented packets. In all cases, these attacks may result in Denial-of-Service conditions. No remote code execution or unauthorized access results from these types of attacks. For devices that are vulnerable only on the control plane, it is important to note that switching services for traffic traversing the device, i.e. the data plane, are not impacted. Software Versions and Fixes When considering software upgrades, please also consult http://www.cisco.com/en/US/products/products_security_advisories_listing.html and any subsequent advisories to determine exposure and a complete upgrade solution. In all cases, customers should exercise caution to be certain the devices to be upgraded contain sufficient memory and that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, contact the Cisco Technical Assistance Center ("TAC") for assistance. IOS-based Products Each row of the Cisco IOS software table (below) describes a release train and the platforms or products for which it is intended. If a given release train is vulnerable, then the earliest possible releases that contain the fix (the "First Fixed Release") and the anticipated date of availability for each are listed in the "Rebuild" and "Maintenance" columns. A device running a release in the given train that is earlier than the release in a specific column (less than the First Fixed Release) is known to be vulnerable. The release should be upgraded at least to the indicated release or a later version (greater than or equal to the First Fixed Release label). For further information on the terms "Rebuild" and "Maintenance" please consult the following URL: http://www.cisco.com/warp/public/620/1.html Due to differences in software availability and in the feature scenarios in which Cisco IOS is vulnerable, the table of first fixed releases has been broken down based on the different vulnerabilities that affect each technology. There are four different groups: TCPv4: represents CSCed78149 ( registered customers only) and CSCef60659 ( registered customers only) . The first Cisco Bug ID tracks TCP's vulnerability to PMTUD attacks, and the second Cisco Bug ID tracks the vulnerability that affects all protocols that make use of PMTUD, with the exception of TCP over IPv6, which is not affected by this vulnerability. Tunnels: represents CSCef60659 ( registered customers only) , CSCef43691 ( registered customers only) , CSCsa61864 ( registered customers only) , CSCsa59600 ( registered customers only) , and CSCef44699 ( registered customers only) . These are the Cisco Bug IDs that track vulnerabilities in most of the affected tunneling protocols (GRE, L2TPv3, and IPSec.) TCPv6: represents CSCef61610 ( registered customers only) , which is the Cisco Bug ID that tracks TCP's vulnerability to PMTUD attacks when running over IPv6. L2TPv2: represents CSCsa52807 ( registered customers only) , which is the Cisco Bug ID that tracks L2TPv2's vulnerability to PMTUD attacks. Major Release Availability of Repaired Releases Affected 12.0-Based Release Rebuild Maintenance 12.0 TCPv4 and Tunnels 12.0(28c) TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0DA TCPv4 and Tunnels Vulnerable; migrate to 12.2(12)DA8 or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0DB TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0DC TCPv4 and Tunnels Vulnerable; migrate to 12.2(15)BC2f or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0S TCPv4 and Tunnels 12.0(27)S5, available 23-May-05 12.0(31)S, available 28-Apr-05 12.0(28)S3, available 25-Apr-05 12.0(30)S1 TCPv6 12.0(27)S5, available 23-May-05 12.0(31)S, available 28-Apr-05 12.0(28)S3, available 25-Apr-05 12.0(30)S1 L2TPv2 Not vulnerable 12.0SC TCPv4 and Tunnels Vulnerable; migrate to 12.2(15)BC2f or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0SL TCPv4 and Tunnels Vulnerable; migrate to 12.0S or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0SP TCPv4 and Tunnels Vulnerable; migrate to 12.0S or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0ST TCPv4 and Tunnels Vulnerable; migrate to 12.0S or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0SX TCPv4 and Tunnels Vulnerable; contact TAC TCPv6 Vulnerable; contact TAC L2TPv2 Not vulnerable 12.0SZ TCPv4 and Tunnels Vulnerable; migrate to 12.0S or later TCPv6 Vulnerable; migrate to 12.0S or later L2TPv2 Not vulnerable 12.0T TCPv4 and Tunnels Vulnerable; migrate to 12.1(27) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0W5 TCPv4 and Tunnels 12.0(25)W5(27c) 12.0(28)W5(31a) TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0WC TCPv4 and Tunnels 12.0(5)WC12, available 25-July-05 TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XA TCPv4 and Tunnels Vulnerable; migrate to 12.1(27) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XB TCPv4 and Tunnels Vulnerable; migrate to 12.1(27) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XC TCPv4 and Tunnels Vulnerable; migrate to 12.1(27) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XD TCPv4 and Tunnels Vulnerable; migrate to 12.1(27) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XE TCPv4 and Tunnels Vulnerable; migrate to 12.1E latest TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XF TCPv4 and Tunnels Vulnerable; migrate to 12.1(27) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XG TCPv4 and Tunnels Vulnerable; migrate to 12.1(27) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XH TCPv4 and Tunnels Vulnerable; migrate to 12.1(27) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XI TCPv4 and Tunnels Vulnerable; migrate to 12.1(27) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XJ TCPv4 and Tunnels Vulnerable; migrate to 12.1(27) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XK TCPv4 and Tunnels Vulnerable; migrate to 12.2(28) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XL TCPv4 and Tunnels Vulnerable; migrate to 12.2(28) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XM TCPv4 and Tunnels Vulnerable; migrate to 12.1(27) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XN TCPv4 and Tunnels Vulnerable; migrate to 12.1(27) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XQ TCPv4 and Tunnels Vulnerable; migrate to 12.1(27) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XR TCPv4 and Tunnels Vulnerable; migrate to 12.2(28) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XS TCPv4 and Tunnels Vulnerable; migrate to 12.1E latest TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.0XV TCPv4 and Tunnels Vulnerable; migrate to 12.1(27) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable Affected 12.1-Based Release Rebuild Maintenance 12.1 TCPv4 and Tunnels 12.1(27) TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1AA TCPv4 and Tunnels Vulnerable; migrate to 12.2(28) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1AX TCPv4 and Tunnels Vulnerable; migrate to 12.2(25)EY or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1AZ TCPv4 and Tunnels Vulnerable; migrate to 12.1(22)EA4 or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1DA TCPv4 and Tunnels Vulnerable; migrate to 12.2(12)DA8 or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1DB TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1DC TCPv4 and Tunnels Vulnerable; migrate to 12.2(15)BC2f or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1E TCPv4 and Tunnels 12.1(22)E6, available 02-May-05 12.1(23)E3, available 02-May-05 12.1(26)E1 TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1EA TCPv4 and Tunnels 12.1(22)EA4 TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1EB TCPv4 and Tunnels Vulnerable; contact TAC TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1EC TCPv4 and Tunnels Vulnerable; migrate to 12.2(15)BC2f or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1EO TCPv4 and Tunnels 12.1(19)EO4, available 26-May-05 TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1EU TCPv4 and Tunnels Vulnerable; migrate to 12.2(20)EU or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1EV TCPv4 and Tunnels Vulnerable; contact TAC TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1EW TCPv4 and Tunnels Vulnerable; migrate to 12.2(18)EW3 or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1EX TCPv4 and Tunnels Vulnerable; migrate to 12.1E latest TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1EY TCPv4 and Tunnels Vulnerable; migrate to 12.1E latest TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1T TCPv4 and Tunnels Vulnerable; migrate to 12.2(28) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XA TCPv4 and Tunnels Vulnerable; migrate to 12.2(28) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XB TCPv4 and Tunnels Vulnerable; migrate to 12.2(28) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XC TCPv4 and Tunnels Vulnerable; migrate to 12.2(28) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XD TCPv4 and Tunnels Vulnerable; migrate to 12.2(28) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XE TCPv4 and Tunnels Vulnerable; migrate to 12.1E latest TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XF TCPv4 and Tunnels Vulnerable; migrate to 12.2(28) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XG TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XH TCPv4 and Tunnels Vulnerable; migrate to 12.2(28) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XI TCPv4 and Tunnels Vulnerable; migrate to 12.2(28) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XJ TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XL TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XM TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XP TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XQ TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XR TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XT TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XU TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1XV TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1YA TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1YB TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1YC TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1YD TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1YE TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1YF TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1YH TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1YI TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.1YJ TCPv4 and Tunnels Vulnerable; migrate to 12.1(22)EA4 or later TCPv6 Not vulnerable L2TPv2 Not vulnerable Affected 12.2-Based Release Rebuild Maintenance 12.2 TCPv4 and Tunnels 12.2(28) TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.2B TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2BC TCPv4 and Tunnels 12.2(15)BC2f TCPv6 Not vulnerable L2TPv2 Vulnerable; contact TAC 12.2BW TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2BY TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2BZ TCPv4 Vulnerable; migrate to 12.3(7)XI3 Tunnels Vulnerable; migrate to 12.3(7)XI5, available TBD TCPv6 Not vulnerable L2TPv2 Vulnerable; contact TAC 12.2CX TCPv4 and Tunnels 12.2(15)BC2f TCPv6 Not vulnerable L2TPv2 Vulnerable; contact TAC 12.2CY TCPv4 and Tunnels 12.2(15)BC2f TCPv6 Not vulnerable L2TPv2 Vulnerable; contact TAC 12.2CZ TCPv4 and Tunnels Vulnerable; contact TAC TCPv6 Not vulnerable L2TPv2 Vulnerable; contact TAC 12.2DA TCPv4 and Tunnels 12.2(12)DA8 TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.2DD TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.2DX TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.2EU TCPv4 and Tunnels 12.2(20)EU TCPv6 Vulnerable; contact TAC L2TPv2 Not vulnerable 12.2EW TCPv4 and Tunnels 12.2(18)EW3 TCPv6 Vulnerable; migrate to 12.2S L2TPv2 Not vulnerable 12.2EWA TCPv4 and Tunnels 12.2(25)EWA TCPv6 12.2(25)EWA L2TPv2 Not vulnerable 12.2EX TCPv4 and Tunnels Vulnerable; migrate to 12.2(25)SEB or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.2EY TCPv4 and Tunnels 12.2(25)EY TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.2JA TCPv4 and Tunnels Vulnerable; migrate to 12.3(4)JA TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.2JK TCPv4 and Tunnels Vulnerable; contact TAC TCPv6 Vulnerable; contact TAC L2TPv2 Vulnerable; contact TAC 12.2MB TCPv4 and Tunnels Vulnerable; contact TAC TCPv6 Vulnerable; contact TAC L2TPv2 Vulnerable; contact TAC 12.2MC TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T TCPv6 Vulnerable; migrate to 12.3(14)T L2TPv2 Vulnerable; migrate to 12.3(14)T 12.2S TCPv4 and Tunnels 12.2(14)S13 12.2(18)S8 12.2(20)S7 12.2(25)S3 TCPv6 12.2(20)S7 12.2(25)S3 L2TPv2 Not vulnerable 12.2SE TCPv4 and Tunnels 12.2(25)SEB TCPv6 12.2(25)SEA vulnerable; migrate to 12.2(25)SEB L2TPv2 Not vulnerable 12.2SO TCPv4 and Tunnels 12.2(18)SO1, available 25-Mar-05 TCPv6 12.2(18)SO2, available 29-Apr-05 L2TPv2 Not vulnerable 12.2SU TCPv4 and Tunnels Vulnerable; contact TAC TCPv6 Vulnerable; contact TAC L2TPv2 Not vulnerable 12.2SV TCPv4 and Tunnels Vulnerable; migrate to 12.2(25)S3 TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.2SW TCPv4 and Tunnels Vulnerable; contact TAC TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.2SX TCPv4 and Tunnels Vulnerable; migrate to 12.2(17d)SXB7 TCPv6 Vulnerable; migrate to 12.2(17d)SXB7 L2TPv2 Not vulnerable 12.2SXA TCPv4 and Tunnels Vulnerable; migrate to 12.2(17d)SXB7 TCPv6 Vulnerable; migrate to 12.2(17d)SXB7 L2TPv2 Not vulnerable 12.2SXB TCPv4 and Tunnels 12.2(17d)SXB7 TCPv6 12.2(17d)SXB7 L2TPv2 Not vulnerable 12.2SXD TCPv4 and Tunnels 12.2(18)SXD4 TCPv6 12.2(18)SXD4 L2TPv2 Not vulnerable 12.2SY TCPv4 and Tunnels Vulnerable; migrate to 12.2(17d)SXB7 TCPv6 Vulnerable; migrate to 12.2(17d)SXB7 L2TPv2 Not vulnerable 12.2SZ TCPv4 and Tunnels Vulnerable; migrate to 12.2(20)S7 TCPv6 Vulnerable; migrate to 12.2(20)S7 L2TPv2 Not vulnerable 12.2T TCPv4 and Tunnels 12.2(15)T15 TCPv6 12.2(15)T15 L2TPv2 Vulnerable; contact TAC 12.2XA TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.2XB TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2XC TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2XD TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2XE TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2XF TCPv4 and Tunnels Vulnerable; migrate to 12.2(15)BC2f TCPv6 Not vulnerable L2TPv2 Vulnerable; contact TAC 12.2XG TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2XH TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2XI TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2XJ TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2XK TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2XL TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2XM TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2XN TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2XQ TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2XR TCPv4 and Tunnels Vulnerable; migrate to 12.3(4)JA TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.2XT TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2XU TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2XW TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2YA TCPv4 and Tunnels 12.2(4)YA9 TCPv6 Not vulnerable L2TPv2 Vulnerable; contact TAC 12.2YB TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2YC TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2YD TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2YE TCPv4 and Tunnels Vulnerable; migrate to 12.2S or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.2S or later 12.2YF TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2YG TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2YH TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2YJ TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3 or later 12.2YK TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.2YL TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2YM TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2YN TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2YO TCPv4 and Tunnels Vulnerable; migrate to 12.2(17d)SXB7 TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.2YQ TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2YR TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2YT TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Vulnerable; migrate to 12.3(12) or later L2TPv2 Vulnerable; migrate to 12.3 or later 12.2YU TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2YV TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2YW TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2YX TCPv4 and Tunnels Vulnerable; contact TAC TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.2YY TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2YZ TCPv4 and Tunnels Vulnerable; migrate to 12.2(20)S7 TCPv6 Vulnerable; migrate to 12.2(20)S7 L2TPv2 Not vulnerable 12.2ZA TCPv4 and Tunnels Vulnerable; migrate to 12.2(17d)SXB7 TCPv6 Vulnerable; migrate to 12.2(17d)SXB7 L2TPv2 Not vulnerable 12.2ZB TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Not vulnerable L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2ZC TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2ZD TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T TCPv6 Vulnerable; migrate to 12.3(14)T L2TPv2 Vulnerable; migrate to 12.3(14)T 12.2ZE TCPv4 and Tunnels Vulnerable; migrate to 12.3(13) or later TCPv6 Vulnerable; migrate to 12.3(12) or later L2TPv2 Vulnerable; migrate to 12.3 or later 12.2ZF TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2ZG TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2ZH TCPv4 and Tunnels 12.2(13)ZH6, available TBD TCPv6 12.2(13)ZH6, available TBD L2TPv2 12.2(13)ZH6, available TBD 12.2ZJ TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2ZK TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2ZL TCPv4 and Tunnels 12.2(15)ZL2, available TBD TCPv6 12.2(15)ZL2, available TBD L2TPv2 12.2(15)ZL2, available TBD 12.2ZN TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.2ZP TCPv4 and Tunnels Vulnerable; contact TAC TCPv6 Vulnerable; contact TAC L2TPv2 Vulnerable; contact TAC Major Release Availability of Repaired Releases Affected 12.3-Based Release Rebuild Maintenance 12.3 TCPv4 and Tunnels 12.3(3h); available 21-Apr-05 12.3(13) 12.3(5e); available 28-Apr-05 12.3(6e) 12.3(9d); available 21-Apr-05 12.3(10c) 12.3(12b); available 12-Apr-05 TCPv6 12.3(6e) 12.3(12) 12.3(3h); available 21-Apr-05 12.3(5e); available 28-Apr-05 12.3(9d); available 21-Apr-05 12.3(10c) L2TPv2 12.3(6e) 12.3(15), available 6-Jun-05 12.3(3h); available 21-Apr-05 12.3(5e); available 28-Apr-05 12.3(9d); available 21-Apr-05 12.3(12b); available 12-Apr-05 12.3(13a); available 2-May-05 12.3B TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.3BC TCPv4 and Tunnels 12.3(9a)BC2 TCPv6 Vulnerable; contact TAC L2TPv2 Vulnerable; contact TAC 12.3BW TCPv4 and Tunnels Vulnerable; migrate to 12.3(7)T8 or later TCPv6 Vulnerable; migrate to 12.3(7)T8 or later L2TPv2 Vulnerable; migrate to 12.3(11)T4 or later 12.3JA TCPv4 and Tunnels 12.3(4)JA TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.3T TCPv4 and Tunnels 12.3(7)T8 12.3(14)T 12.3(8)T7 12.3(11)T4 TCPv6 12.3(7)T8 12.3(14)T 12.3(8)T7 12.3(11)T4 L2TPv2 12.3(11)T4 12.3(14)T 12.3(7)T10; available 16-May-05 12.3XA TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.3XB TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.3XC TCPv4 and Tunnels 12.3(2)XC3, available TBD TCPv6 12.3(2)XC3, available TBD L2TPv2 12.3(2)XC3, available TBD 12.3XD TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.3XE TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.3XF TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.3XG TCPv4 and Tunnels Vulnerable; contact TAC TCPv6 Vulnerable; contact TAC L2TPv2 Vulnerable; contact TAC 12.3XH TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.3XI TCPv4 12.3(7)XI3 Tunnels 12.3(7)XI5, available TBD TCPv6 12.3(7)XI3 L2TPv2 Vulnerable; contact TAC 12.3XJ TCPv4 and Tunnels Vulnerable; contact TAC TCPv6 Vulnerable; contact TAC L2TPv2 Vulnerable; contact TAC 12.3XK TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.3XL TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.3XM TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.3XQ TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.3XR TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.3XS TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T TCPv6 Vulnerable; migrate to 12.3(14)T L2TPv2 Vulnerable; migrate to 12.3(14)T 12.3XT TCPv4 and Tunnels Vulnerable; migrate to 12.3(4)JA TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.3XU TCPv4 and Tunnels Vulnerable; contact TAC TCPv6 Vulnerable; contact TAC L2TPv2 Vulnerable; contact TAC 12.3XW TCPv4 and Tunnels Vulnerable; migrate to 12.3(11)YF2 or later TCPv6 Vulnerable; migrate to 12.3(11)YF2 or later L2TPv2 Vulnerable; migrate to 12.3(11)YF2 or later 12.3XX TCPv4 and Tunnels Vulnerable; migrate to 12.3(14)T or later TCPv6 Vulnerable; migrate to 12.3(14)T or later L2TPv2 Vulnerable; migrate to 12.3(14)T or later 12.3XY TCPv4 and Tunnels 12.3(8)XY4 TCPv6 Not vulnerable L2TPv2 Not vulnerable 12.3YA TCPv4 and Tunnels Vulnerable; contact TAC TCPv6 Vulnerable; contact TAC L2TPv2 Vulnerable; contact TAC 12.3YD TCPv4 and Tunnels Vulnerable; contact TAC TCPv6 Vulnerable; contact TAC L2TPv2 Vulnerable; contact TAC 12.3YF TCPv4 and Tunnels 12.3(11)YF2, available 12-May-05 TCPv6 12.3(11)YF2, available 12-May-05 L2TPv2 12.3(11)YF2, available 12-May-05 12.3YG TCPv4 and Tunnels 12.3(8)YG1 TCPv6 12.3(8)YG1 L2TPv2 Vulnerable; contact TAC 12.3YH TCPv4 and Tunnels Vulnerable; contact TAC TCPv6 Vulnerable; contact TAC L2TPv2 Vulnerable; contact TAC 12.3YI TCPv4 and Tunnels 12.3(8)YI TCPv6 12.3(8)YI L2TPv2 12.3(8)YI 12.3YJ TCPv4 and Tunnels Vulnerable; contact TAC TCPv6 Vulnerable; contact TAC L2TPv2 Vulnerable; contact TAC 12.3YK TCPv4 and Tunnels 12.3(11)YK TCPv6 12.3(11)YK L2TPv2 Vulnerable; contact TAC 12.3YN TCPv4 and Tunnels 12.3(11)YN TCPv6 Vulnerable; contact TAC L2TPv2 Vulnerable; contact TAC 12.3YQ TCPv4 and Tunnels 12.3(14)YQ TCPv6 12.3(14)YQ L2TPv2 12.3(14)YQ Non-IOS-based Products Each row of the non-IOS-based products table (below) lists the earliest possible release that contains the fix (the "First Fixed Release") and the anticipated date of availability. A product running a release that is earlier than the listed release (less than the First Fixed Release) is known to be vulnerable. The product should be upgraded at least to the indicated release or a later release (greater than or equal to the First Fixed Release label.) Product Bug ID First Fixed Release IOS XR CSCef45332 ( registered customers only) SMU ID AA01157 for IOS XR 3.0.0. Download from https://www.cisco.com/cgi- bin/Support/FileExg/IOSXR_30.cgi SMU ID AA01172 for IOS XR 3.0.1. Download from https://www.cisco.com/cgi- bin/Support/FileExg/IOSXR_30.cgi 7960 (SCCP) CSCef46728 ( registered customers only) 7.1(1) 7970 (SCCP) CSCef54947 ( registered customers only) 6.0(3) 7960 (SIP) CSCef54204 ( registered customers only) and CSCef54206 ( registered customers only) Release date not determined yet. Cisco PIX Security Appliance CSCef57566 ( registered customers only) 6.2.4(101) and 6.3.4(120), both available from http://www.cisco.com/pcgi- bin/tablebuild.pl/PIXPSIRT. Catalyst 6608 and 6624 CSCsa60692 ( registered customers only) D00404000018 (load 18, DSP Ver 4.3.25) for the 6608 and A00204000010 (load 10, DSP Ver 4.3.25) for the 6624. Release date for fixed CFB and MTP loads has not been determined yet. Cisco 11000 and 11500 Content Services Switches CSCeh45454 ( registered customers only) Release date not determined yet. Cisco Global Site Selector CSCeh20083 ( registered customers only) Release date not determined yet. Cisco MDS 9000 Series Multilayer Switches CSCeh04183 ( registered customers only) SAN-OS 2.1(1a) VPN 5000 Concentrator CSCeh59823 ( registered customers only) Please contact TAC. ONS 15454 IOS-based blades (ML and SL) See Cisco bug IDs for Cisco IOS R5.0 ONS 15302 and ONS 15305 - R2.0 Cisco MGX-8250 and MGX-8850 CSCeh65337 ( registered customers only) and CSCeh63449 ( registered customers only) for the Cisco MGX2 Release date not determined yet Voice and IP Communication Products Using Cisco-Customized Microsoft Windows - win-OS-Upgrade-k9.2000-2-7sr3.exe; available 26-Apr-2005 Cisco ACS Solution Engine CSCeh62307 ( registered customers only) Release date not determined yet For all Cisco products that are based on a third party Operating System and when Cisco is not supplying the OS, please contact your respective vendor for the appropriate patches. Obtaining Fixed Software Customers with Service Contracts Customers with contracts should obtain upgraded software through their regular update channels. For most customers, this means that upgrades should be obtained through the Software Center on Cisco's worldwide website at http://www.cisco.com. Customers using Third-party Support Organizations Customers whose Cisco products are provided or maintained through prior or existing agreement with third-party support organizations such as Cisco Partners, authorized resellers, or service providers should contact that support organization for assistance with the upgrade, which should be free of charge. Customers without Service Contracts Customers who purchase direct from Cisco but who do not hold a Cisco service contract and customers who purchase through third-party vendors but are unsuccessful at obtaining fixed software through their point of sale should get their upgrades by contacting the Cisco Technical Assistance Center (TAC). TAC contacts are as follows. +1 800 553 2447 (toll free from within North America) +1 408 526 7209 (toll call from anywhere in the world) e-mail: tac@cisco.com Please have your product serial number available and give the URL of this notice as evidence of your entitlement to a free upgrade. Free upgrades for non-contract customers must be requested through the TAC. Please do not contact either "psirt@cisco.com" or "security-alert@cisco.com" for software upgrades. If you need assistance with the implementation of the workarounds, or have questions on the workarounds, please contact the Cisco Technical Assistance Center (TAC). Customers may only install and expect support for the feature sets they have purchased. By installing, downloading, accessing, or otherwise using such software upgrades, customers agree to be bound by the terms of Cisco's software license terms found at http://www.cisco.com/public/sw-license-agreement.html, or as otherwise set forth at Cisco.com Downloads at http://www.cisco.com/public/sw- center/sw-usingswc.shtml Workarounds The effectiveness of any workaround is dependent on specific customer situations such as product mix, network topology, traffic behavior, and organizational mission. Due to the variety of affected products and releases, customers should consult with their service provider or support organization to ensure any applied workaround is the most appropriate for use in the intended network before it is deployed. Effects of Disabling PMTUD As will be shown next, one of the most common workarounds to mitigate the effect of attacks based on crafted ICMP "fragmentation needed and DF bit set" messages (or ICMPv6 "message too big" messages) is to disable PMTUD when it is possible to do so through configuration commands. It is important to note that in general, there should not be negative side effects to disabling PMTUD. Disabling PMTUD will cause a device to send its datagrams with the DF bit cleared. When the large packets reach a small-MTU router, that router will fragment the packets into multiple smaller ones. The smaller, fragmented data will then reach the destination, where it will be reassembled into the original large packet. Another consideration is that when PMTUD is disabled for TCP, TCP will not adjust its MSS based on changes in the Path MTU, and the actual MSS that will be used could cause unnecessary segmentation if its value is larger than the Path MTU. The MSS value that will be used will be a manually-set value (through a configuration command) or if nothing is explicitly configured, a default of 536 bytes if the destination is remote, or the outgoing interface's MTU minus 40 bytes (20 bytes for the size of the IP header and 20 bytes for the size of the TCP header) if the destination is local. To avoid unnecessary segmentation, it is recommended that the MSS be manually set to a value small enough to pass through the smallest MTU in the data path. Note: in the particular case of Cisco IOS, the MSS value cannot be set manually (via the command ip tcp mss ) when PMTUD is disabled due to an implementation detail. The actual MSS that will be used when PMTUD is disabled will be 536 bytes if the destination is remote, or the interface's MTU minus 40 bytes (1460 bytes for Ethernet, for example) if the destination is local. Finally, please note that in general, disabling PMTUD will have no effect on existing connections, which means that existing connections must be manually terminated and re-established for the new PMTUD setting to take effect. Voice Applications, PIX Security Appliance and PMTUD Disabling PMTUD on devices that are running voice applications (like the Cisco CallManager) can create an undesirable condition if the voice traffic is passing through a Cisco PIX Security Appliance and the PIX Security Appliance is doing fixups of voice protocols like SCCP (fixup protocol skinny), SIP (fixup protocol sip) and H.323 (fixup protocol h323) Note: the default installation of the Cisco CallManager has PMTUD disabled. The problem occurs because the PIX Security Appliance/FWSM software cannot always fully inspect voice-signaling traffic that has segmented and/or fragmented protocol data units (PDUs). With PMTUD disabled, sufficiently large PDUs may be split across multiple TCP segments or IP fragments, which can cause a failure to properly open the pinholes for secondary connections and media traffic. Therefore, when deciding to disable PMTUD on devices running voice applications, take care to provision the access rules to permit the necessary secondary signaling and media traffic and to disable the respective protocol's fixup. Depending on the local security policy, the requirement of pre-opening ports may render this workaround of disabling PMTUD inapplicable. Effects of Filtering Out ICMP Unreachable Messages Another suggested workaround, especially in the case of IPSec and of those products where it is not possible to disable PMTUD, is to filter out ICMP "fragmentation needed and DF bit set" messages. It is important to note that any recommendation to block ICMP "fragmentation needed and DF bit set" messages applies to messages that are destined to the device that is being protected, and not for messages destined elsewhere in the network. Indiscriminately blocking ICMP unreachable messages can lead to the creation of the "black holes" described in RFC 2923 ("TCP Problems with Path MTU Discovery" - http://www.ietf.org/rfc/rfc2923.txt ). Additionally, if ICMP "fragmentation needed and DF bit set" messages are blocked from being received by an end host, the end host must send packets with the DF bit cleared. This can be accomplished by disabling PMTUD, or, if there is no way to achieve this, by using special mechanisms like "crypto ipsec df-bit clear" where supported (in the case of IPSec). If ICMP unreachables are being blocked, and packets are sent with the DF bit set, then the end host will never be able to react to the situation where an intermediate router needs to fragment packets that are too big for a certain PMTU; this situation requires either fragmenting the packet at the source (end host), or re-sending the packet with the DF bit cleared. Workarounds for Cisco IOS Transmission Control Protocol Over IP Version 4 If PMTUD has been explicitly enabled, a possible workaround to prevent PMTUD attacks is to disable it by using the global configuration command no ip tcp path- mtu-discovery. Once this command is executed, PMTUD will be disabled for all new TCP connections; configuring PMTD on the IOS device does not have any effect on existing TCP sessions already established from/to the router. Please note that with PMTUD disabled, the MSS that will be used will be the value set with the ip tcp mss command, or the default of 536 bytes for remote destinations, or 1460 bytes for local destinations. Transmission Control Protocol Over IP Version 6 PMTUD is enabled by default when using TCP over IPv6, and it is not possible to disable it. For this reason a possible workaround is to use an ACL to block the ICMPv6 "packet too big" message. Please note that filtering out ICMPv6 "packet too big" messages means that the layer 3 (IPv6) PMTUD is being shut down as well. Therefore, it is necessary to make sure that the MTU is set on the end host to the lowest possible IPv6 MTU - 1280 bytes. Otherwise, since the device is not seeing the "packet too big" message, the device will not know that an intermediate system has dropped a packet because it was too big. ICMPv6 "packet too big" messages are the IPv6 equivalent to the ICMPv4 "fragmentation needed and DF bit set" message. Therefore, the same considerations presented in the section Effects of Filtering Out ICMP Unreachable Messages apply to filtering out ICMPv6 "packet too big" messages. IPSec For IPSec, the recommended workaround is to "disable" PMTUD. Please note that there is not a single command to disable PMTUD under IPSec, but this can be achieved through other mechanisms. In particular, the following two things must be done: Filter out ICMP "fragmentation needed and DF bit set" messages (type 3, code 4) destined to the router itself using an Access Control List or the Control Plane Policing (CoPP) feature. The following example shows how to block ICMP "fragmentation needed and DF bit set" (type 3, code 4) messages that are addressed to any of the device's IP addresses using an interface ACL (note how the type 3, code 4 message is specified using the packet-too-big keyword): access-list 111 deny icmp any host packet-too-big access-list 111 deny icmp any host packet-too-big access-list 111 deny icmp any host packet-too-big access-list 111 permit ip any any ! interface fastEthernet 0/0 ip access-group 111 in ! interface fastEthernet 0/1 ip access-group 111 in ! interface fastEthernet 0/2 ip access-group 111 in Note: for this workaround to be effective, all of the router's IP addresses must be included in the ACL and the ACL must be applied to all interfaces. This type of filtering could be implemented as part of an Infrastructure ACL, which is a networking best practice. For more information on iACLs, refer to "Protecting Your Core: Infrastructure Protection Access Control Lists" at http://www.cisco.com/warp/public/707/iacl.html. The following example shows how to use Control Plane Policing to accomplish the same thing: access-list 140 permit icmp any host packet-too-big access-list 140 permit icmp any host packet-too-big [...] access-list 140 permit icmp any host packet-too-big access-list 140 deny ip any any ! class-map match-all icmp-class match access-group 140 ! policy-map control-plane-policy ! Drop all traffic that matches the class "icmp-class" class icmp-class drop ! control-plane service-policy input control-plane-policy Note: CoPP is available in IOS release trains 12.0S, 12.2S and 12.3T. Additional information on the configuration and use of the CoPP feature can be found at the following URL: http://www.cisco.com/en/US/products/sw/iosswrel/ps1838/products_feature_guide09186a 00801afad4.html Allow IPSec to fragment the embedded packet even when the DF bit is set. This can be accomplished by using the command crypto ipsec df-bit clear (which is available in IOS 12.2(2)T and later) or by using Policy-Based Routing (PBR) (available in IOS 12.1(6) and later) to clear the DF bit. What follows is an example of how to use PBR to clear the DF bit: route-map clear-df permit 10 match ip address 101 !--- The following command is used to change the !--- Don't Fragment (DF) bit value in the IP header; !--- it must be used in route-map configuration mode. set ip df 0 access-list 101 permit tcp 10.1.3.0 0.0.0.255 any interface ethernet0 ... !--- The following command is used to identify a !--- route map to use for policy routing on an !--- interface; if must be used in interface !--- configuration mode. ip policy route-map clear-df In this example the route-map is applied to the interface where the unencrypted traffic enters the router, and 10.1.3.0/24 is the address space that is sending traffic through the IPSec tunnel. Generic Routing Encapsulation and IPinIP The only workaround for this case is to disable PMTUD on the tunnel interface if it has been enabled. This is accomplished via the command no tunnel path-mtu- discovery, while in the specific tunnel interface configuration mode. Without the tunnel path-mtu-discovery command configured, the DF bit will always be cleared in the GRE IP header. This allows the GRE IP packet to be fragmented, even though the encapsulated data IP header had the DF bit set, which normally wouldn't allow the packet to be fragmented. Please note that if you are using GRE with IPSec you need to use the command no tunnel path-mtu-discovery instead of the command crypto ipsec df-bit clear to make sure that DF bit is cleared in transmitted packets; and you also need to filter out ICMP "fragmentation needed and DF bit set" messages (type 3, code 4) destined to the router itself using an Access Control List or the Control Plane Policing (CoPP) feature as described above. If you have an image that is fixed for Cisco Bug ID CSCef44699 ( registered customers only) you can set a low limit on the MTU that is learned via the PMTUD process by using the new command tunnel path-mtu-discovery min-mtu under the specific tunnel interface configuration mode. Layer 2 Tunneling Protocol Version 2 and Layer 2 Tunneling Protocol Version 3 The only workaround to protect Layer 2 Tunneling Protocol sessions (both versions 2 and 3) against PMTUD attacks is to disable PMTUD if it has been enabled. For L2TPv2, this is done via the no ip pmtu command in vpdn-group configuration mode as shown here: router(config)#vpdn enable router(config)#vpdn-group 1 router(config-vpdn)#no ip pmtu For L2TPv3, this is done via the commands no ip pmtu and no ip dfbit set in pseudowire-class configuration mode as shown here: pseudowire-class [pseudowire class name] encapsulation l2tpv3 no ip pmtu no ip dfbit set [...] For L2TPv2, if you have an image that is fixed for Cisco Bug ID CSCsa52807 ( registered customers only) you can set low and high limits on the MTU that is learned via the PMTUD process by using the new commands vpdn pmtu minimum and vpdn pmtu maximum under vpdn-group configuration mode. Workarounds for IOS XR If a Cisco CRS-1 is establishing TCP sessions with other peers, then there are no configuration workarounds and customers are recommended to either apply a SMU or upgrade to a non-vulnerable version of IOS XR. Workarounds for Cisco IP Phones There are no workarounds for ICMP "hard" error and "source quench" attacks against Cisco IP Phones. However, these attacks can be mitigated by segmenting voice and data through the use of VLAN technologies, and in general, by following recommended best practices for IP telephony such as those documented in the white paper "SAFE: IP Telephony Security in Depth" available at http://www.cisco.com/en/US/netsol/ns340/ns394/ns171/ns128/networking_solutions_whit e_paper09186a00801b7a50.shtml. Workarounds for the Cisco PIX Security Appliance As mentioned in the Vulnerable Products section, the PIX Security Appliance is only affected if IPSec is configured and enabled. If it is affected, then there are no workarounds (since PMTUD cannot be disabled on the PIX Security Appliance) and customers are recommended to upgrade to a non-vulnerable version of the PIX Security Appliance software. While it does not prevent PMTUD attacks, the command clear ipsec sa gives the administrator a way to reset the Security Association and restore the Path MTU for the tunnel to its original value. Workarounds for Cisco VPN 5000 Concentrator It is possible to completely disable PMTUD by setting the configuration directive PreTunnelFragmentation to "no". Even if PreTunnelFragmentation is left on with the "yes" setting, it is worth noting that the VPN 5000 has very strict access rules for incoming packets. If the attack were to originate from the outside (interface Ethernet 1), then the packets would always be dropped and have no effect on the IPSec connection. Packets coming across the tunnel or originating from the inside interface (Ethernet 0) would still be vulnerable to PMTUD attacks. Some customers run the device in "single-arm mode," where only Ethernet 0 is connected and terminates tunnels. Customers under this scenario are vulnerable. Workarounds for Other Operating Systems Cisco has products that run on top of other operating systems, like Microsoft Windows and different versions of Unix. These products normally run as end hosts, i.e. not as intermediate systems. Therefore, they may be affected by the vulnerabilities described in this document if the operating systems are vulnerable. Some of the workarounds presented in this section, in particular disabling PMTUD, may also be valid workarounds for these operating systems. For information on how to disable Path MTU on Microsoft Windows and several versions of Unix you can consult the document "Adjusting IP MTU, TCP MSS, and PMTUD on Windows and Sun Systems" available at http://cisco.com/en/US/tech/tk870/tk472/tk473/technologies_tech_note09186a008011a21 8.shtml. Protecting Against ICMP Source Quench Attacks The ICMP "source quench" message was an early attempt at handling network congestion, but current standards recognize that it is not an effective method for handling this scenario. For this reason most modern TCP/IP implementations ignore receipt of such a message and do not send them. This situation should make it relatively safe to filter out ICMP "source quench" messages on both vulnerable devices and on the edge of your network. Protecting Against Spoofed Packets While considered as Network Best Practices, features like Unicast Reverse Path Forwarding (uRPF), IP source verify, DHCP Lease Query, Dynamic ACLs with AAA, and mini-ACLs (also with AAA) that help to mitigate problems that are caused by spoofed IP source addresses may be ineffective to mitigate attacks based on ICMP messages when these ICMP packets are not spoofed. The reason for this is that attackers do not necessarily need to spoof the source address of their packets to exploit this vulnerability. However, if an attacker spoofs packets, implementation of anti- spoofing mechanisms at the edge of the network will help mitigate the attack. For more information on anti-spoofing refer to http://www.cisco.com/en/US/tech/tk648/tk361/technologies_tech_note09186a0080120f48. shtml#sec_ip and RFC 2827 ("Network Ingress Filtering: Defeating Denial of Service Attacks which employ IP Source Address Spoofing" - http://www.ietf.org/rfc/rfc2827.txt .) The uRPF feature of IOS helps to mitigate problems that are caused by spoofed IP source addresses. To enable uRPF, use the following commands: router(config)# ip cef router(config)# interface router(config-if)# ip verify unicast reverse-path Please consult the feature guide Unicast Reverse Path Forwarding Loose Mode and ftp://ftp-eng.cisco.com/cons/isp/security/URPF-ISP.pdf for further details on how uRPF works and how to configure it in various scenarios. This is especially important if you are using asymmetric routing. Exploitation and Public Announcements The Cisco PSIRT is not aware of any malicious use of the vulnerabilities described in this advisory. NISCC is issuing a public notice of this industry-wide issue. We would like to thank Fernando Gont of Argentina's Universidad Tecnologica Nacional/Facultad Regional Haedo for reporting the ICMP "source quench" and "hard" error issues to us. Mr. Gont's full research paper on ICMP blind connection-reset and throughput-reduction attacks against TCP, including his research on the PMTU issue can be seen at http://www.gont.com.ar/drafts/icmp-attacks-against-tcp.html . Status of This Notice: FINAL THIS ADVISORY IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTY OF MERCHANTABILITY. YOUR USE OF THE INFORMATION ON THE ADVISORY OR MATERIALS LINKED FROM THE ADVISORY IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS NOTICE AT ANY TIME. A stand-alone copy or paraphrase of the text of this security advisory that omits the distribution URL in the following section is an uncontrolled copy, and may lack important information or contain factual errors. Distribution This advisory will be posted on Cisco's worldwide website at http://www.cisco.com/warp/public/707/cisco-sa-20050412-icmp.shtml In addition to worldwide web posting, a text version of this notice is clear-signed with the Cisco PSIRT PGP key and is posted to the following e-mail and Usenet news recipients. cust-security-announce@cisco.com first-teams@first.org (includes CERT/CC) bugtraq@securityfocus.com cisco@spot.colorado.edu cisco-nsp@puck.nether.net full-disclosure@lists.grok.org.uk comp.dcom.sys.cisco@newsgate.cisco.com Future updates of this advisory, if any, will be placed on Cisco's worldwide website, but may or may not be actively announced on mailing lists or newsgroups. Users concerned about this problem are encouraged to check the above URL for any updates. Revision History Revision 1.2 2005-April-22 Added the following additional products to the list of non-vulnerable products: Cisco 7902/05 and 7920 IP Phones. Cisco LocalDirector. Added the following products to the list of vulnerable products: Cisco MGX-8250 and MGX-8850. Cisco Content Switching Module (CSM) - only management connections are vulnerable. Microsoft Windows is vulnerable to PMTUD attacks and attacks based on ICMP "hard" error messages according to Microsoft Security Bulletin MS05-019 . All Cisco products that are shipped with, or run on top of, Microsoft Windows have been moved to the Vulnerable Products section. Information about the following releases in the table of fixed IOS software has been updated: 12.1(23)E4 (replaced with 12.1(23)E3), 12.1(22)E6, 12.3(11)YF2, 12.3XW, 12.3XS, 12.3XX, 12.3XR, 12.3XQ, 12.3XK, 12.3XE, 12.2EW, 12.2BZ, and 12.3XI. The Cisco MDS9000 is vulnerable to PMTUD attacks in addition to "source quench" attacks. State that for the case of GRE, IPinIP and L2TPv2 it is not possible to authenticate ICMP error messages and that the Cisco Bug IDs for these tunneling protocols add new configuration commands to set a minimum Path MTU. Clarify that the 6608 running Conference Bridge and Transcoder/MTP firmware are also vulnerable. Cisco PIX Security Appliance: 1) clarify that only traffic going through an IPSec tunnel is affected if that tunnel is attacked with a PMTUD attack, 2) clarify that version 7.0 and later of the PIX Security Appliance software is not affected by these vulnerabilities, and 3) mention the clear ipsec sa command as a way to restore a Path MTU in case of a PMTUD attack. Corrected name of first release of the Cisco-customized Microsoft Windows that has PMTUD disabled by default (2000.2.5 instead of 2000.2.6). Point out that Cisco MeetingPlace also uses this same OS customization. Added link to download page for Cisco IOS XR software. For IOS XR, emphasize that users can apply an SMU to fix the ICMP vulnerabilities instead of performing a full IOS XR upgrade. Clarify that when PMTUD is disabled for TCP connections in Cisco IOS, the command ip tcp mss does not have any effect on the MSS and that the MSS that will be used will be 536 bytes or (interfaces's MTU - 40 bytes) depending on whether the destination is remote. Clarify that when GRE is used with IPSec, the command no tunnel path-mtu-discovery should be used instead of crypto ipsec df-bit clear to clear the DF bit of transmitted packets. GSS version 1.2 and earlier are affected. It was previously stated that it was version 1.1 and earlier. Revision 1.1 2005-April-12 Updated Distribution section with new e-mail/Usenet news recipient: full- disclosure@lists.grok.org.uk Revision 1.0 2005-April-12 Initial Public Release Cisco Security Procedures Complete information on reporting security vulnerabilities in Cisco products, obtaining assistance with security incidents, and registering to receive security information from Cisco, is available on Cisco's worldwide website at http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html. This includes instructions for press inquiries regarding Cisco security notices. All Cisco security advisories are available at http://www.cisco.com/go/psirt. -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Updated: Apr 23, 2005 Document ID: 64520 -------------------------------------------------------------------------------- [***** End Cisco Security Advisory Document ID: 64520 *****] _______________________________________________________________________________ CIAC wishes to acknowledge the contributions of Cisco for the information contained in this bulletin. _______________________________________________________________________________ CIAC, the Computer Incident Advisory Capability, is the computer security incident response team for the U.S. Department of Energy (DOE) and the emergency backup response team for the National Institutes of Health (NIH). CIAC is located at the Lawrence Livermore National Laboratory in Livermore, California. CIAC is also a founding member of FIRST, the Forum of Incident Response and Security Teams, a global organization established to foster cooperation and coordination among computer security teams worldwide. CIAC services are available to DOE, DOE contractors, and the NIH. CIAC can be contacted at: Voice: +1 925-422-8193 (7x24) FAX: +1 925-423-8002 STU-III: +1 925-423-2604 E-mail: ciac@ciac.org Previous CIAC notices, anti-virus software, and other information are available from the CIAC Computer Security Archive. World Wide Web: http://www.ciac.org/ Anonymous FTP: ftp.ciac.org PLEASE NOTE: Many users outside of the DOE, ESnet, and NIH computing communities receive CIAC bulletins. If you are not part of these communities, please contact your agency's response team to report incidents. Your agency's team will coordinate with CIAC. The Forum of Incident Response and Security Teams (FIRST) is a world-wide organization. A list of FIRST member organizations and their constituencies can be obtained via WWW at http://www.first.org/. This document was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor the University of California nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial products, process, or service by trade name, trademark, manufacturer, or otherwise, does not necessarily constitute or imply its endorsement, recommendation or favoring by the United States Government or the University of California. The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States Government or the University of California, and shall not be used for advertising or product endorsement purposes. LAST 10 CIAC BULLETINS ISSUED (Previous bulletins available from CIAC) P-169: Cisco Security Advisory: Vulnerabilities in the Internet Key Exchange Xauth Implementation P-170: Cisco Security Advisory: Vulnerabilities in Cisco IOS Secure Shell Server P-171: SGI Advanced Linux Environment 3 Security Update #33 P-172: SGI IRIX gr_osview File Overwrite Vulnerabilities P-173: Cumulative Security Update for Internet Explorer P-174: Vulnerability in Exchange Server P-175: Vulnerability in MSN Messenger (896597) P-176: Vulnerabilities in Microsoft Word (890169) P-177: Vulnerabilities in TCP-IP (893066) P-178: Vulnerability in Message Queuing (892944) P-179: Vulnerability in Windows Shell (893086) P-180: Vulnerabilities in Windows Kernel (890859)